Virgozap, WD SmartWare should automatically activate by detecting your WD Passport Ultra. Please confirm if Dropbox access is an available option in order to confirm if WD SmartWare Pro has been successfully activated. The key symbol may not be present if SmartWare Pro was activated prior to upgrading to a later version of SmartWare. An active Pro license will be retained.
Important:
WD Smartware Pro and Dropbox Notice
Dropbox
WD Smartware Pro
|
Issue:
The activation of WD SmartWare Pro license fails with the message:
'No Internet access detected. Please check your Internet connection and try again'
Cause:
The message No Internet access detected can occur when there's a network communication issue between the PC were SmartWare is installed and the SmartWare Pro license activation server.
Solution:
Important:The instructions below are designed to assist in troubleshooting SmartWare Pro license activation issues. Please try one solution at a time and test for resolution before continuing with the next item. |
- Ensure the computer has a valid Internet connection by opening a web browser to support.wdc.com.
- Ensure the computer were WD SmartWare is installed can resolve the following hostnames to there IP addresses.
nslookup smartware.wdc.com
nslookup wdscoradb01.wdc.com
- Check the local PC Anti-Virus, Malware and/or End Point Protection software to ensure that incoming and outgoing traffic is not blocked for the following online resources..
smartware.wdc.com
multiple IP addresses
ports 80 and 443
wdscoradb01.wdc.com
IP address 10.4.32.242
port 5002
- Check the Router's Internet security and/or firewall settings to ensure that incoming traffic from SmartWare online resources are not blocked.
- Change the DNS Servers in the router to use a public DNS Server such as Google or other DNS server
Primary DNS Server: 8.8.8.8Secondary DNS Server: 8.8.4.4
Note:Please refer to your router's user manual or contact your router's technical support department for the proper procedures.
Important: Power Cycle all devices after any network changes in the following order:
- Reboot the Router
- Reboot the PC or MAC being used
- Reboot the My Cloud device
- Reset the Winsock Catalog to a clean state by opening a command prompt as Administrator using the the following command:
Reboot the computer to complete this operation.
netsh winsock reset
- Connect the PC and or Wi-Fi router to a different network were incoming traffic is not being blocked and activate the SmartWare Pro license
- Contact your Network Administratior or ISP to ensure that incoming traffic from SmartWare online resources are not blocked.
- Windows .NET corruption
The Microsoft .NET Framework Repair Tool detects and tries to repairs frequently occurring issues with the setup of Microsoft .NET Framework or with updates to the Microsoft .NET Framework.
Click Here to download and run the Microsoft .NET Framework Repair Tool. - Disable the computer Network Interface Card (NIC)
- Left click Start Menu
- Left click Control Pannel
- Double click the Network and Internet
- Double click Network and Sharing Center
- Double click Change Adapter Settings
- Right click Local Area Connection if the computer is on a wired Etherent connection,If the computer is on wireless, right click Wireless Area Connection
- Left click Disable
- Activate WD SmartWare Pro
- Enable the computer NIC
- Left click Start Menu
- Left click Control Pannel
- Double click the Network and Internet
- Double click Network and Sharing Center
- Double click Change Adapter Settings
- Right click Local Area Connection if the computer is on a wired Etherent connection,If the computer is on wireless, right click Wireless Area Connection
- Left click Enable
- Reboot the computer
Applied Products:
My Cloud | My Cloud Mirror | My Cloud Mirror (Gen 2) |
My Cloud EX2 | My Cloud EX2 Ultra | My Cloud EX4 |
My Cloud EX2100 | My Cloud DL2100 | My Cloud PR2100 |
My Cloud EX4100 | My Cloud DL4100 | My Cloud PR4100 |
Knowledge Base
Frequently Asked Questions
Answer ID 17221 | Last Updated 07/25/2018
Share
Print<---->
Important:
WD Smartware Pro and Dropbox Notice
Dropbox
WD Smartware Pro
|
The activation of WD SmartWare Pro license fails with the message:
'No Internet access detected. Please check your Internet connection and try again'
The message No Internet access detected can occur when there's a network communication issue between the PC were SmartWare is installed and the SmartWare Pro license activation server.
Important:The instructions below are designed to assist in troubleshooting SmartWare Pro license activation issues. Please try one solution at a time and test for resolution before continuing with the next item. |
- Ensure the computer has a valid Internet connection by opening a web browser to support.wdc.com.
- Ensure the computer were WD SmartWare is installed can resolve the following hostnames to there IP addresses.
nslookup smartware.wdc.com
nslookup wdscoradb01.wdc.com
- Check the local PC Anti-Virus, Malware and/or End Point Protection software to ensure that incoming and outgoing traffic is not blocked for the following online resources..
smartware.wdc.com
multiple IP addresses
ports 80 and 443
wdscoradb01.wdc.com
IP address 10.4.32.242
port 5002
- Check the Router's Internet security and/or firewall settings to ensure that incoming traffic from SmartWare online resources are not blocked.
- Change the DNS Servers in the router to use a public DNS Server such as Google or other DNS server
Primary DNS Server: 8.8.8.8Secondary DNS Server: 8.8.4.4
Note:Please refer to your router's user manual or contact your router's technical support department for the proper procedures.
Important: Power Cycle all devices after any network changes in the following order:
- Reboot the Router
- Reboot the PC or MAC being used
- Reboot the My Cloud device
- Reset the Winsock Catalog to a clean state by opening a command prompt as Administrator using the the following command:
Reboot the computer to complete this operation.
netsh winsock reset
- Connect the PC and or Wi-Fi router to a different network were incoming traffic is not being blocked and activate the SmartWare Pro license
- Contact your Network Administratior or ISP to ensure that incoming traffic from SmartWare online resources are not blocked.
- Windows .NET corruption
The Microsoft .NET Framework Repair Tool detects and tries to repairs frequently occurring issues with the setup of Microsoft .NET Framework or with updates to the Microsoft .NET Framework.
Click Here to download and run the Microsoft .NET Framework Repair Tool. - Disable the computer Network Interface Card (NIC)
- Left click Start Menu
- Left click Control Pannel
- Double click the Network and Internet
- Double click Network and Sharing Center
- Double click Change Adapter Settings
- Right click Local Area Connection if the computer is on a wired Etherent connection,If the computer is on wireless, right click Wireless Area Connection
- Left click Disable
- Activate WD SmartWare Pro
- Enable the computer NIC
- Left click Start Menu
- Left click Control Pannel
- Double click the Network and Internet
- Double click Network and Sharing Center
- Double click Change Adapter Settings
- Right click Local Area Connection if the computer is on a wired Etherent connection,If the computer is on wireless, right click Wireless Area Connection
- Left click Enable
- Reboot the computer
My Cloud | My Cloud Mirror | My Cloud Mirror (Gen 2) |
My Cloud EX2 | My Cloud EX2 Ultra | My Cloud EX4 |
My Cloud EX2100 | My Cloud DL2100 | My Cloud PR2100 |
My Cloud EX4100 | My Cloud DL4100 | My Cloud PR4100 |
Rate answer 1 of 5Rate answer 2 of 5Rate answer 3 of 5Rate answer 4 of 5Rate answer 5 of 5
Please tell us how we can make this answer more useful.
Answers others found helpful
Find Answers
Contact Us
Ask a QuestionSubmit a question to our support team.
Give Feedback
How can we make this site more useful for you?